国产一级a毛一级a看免费视频,久久久久久国产一级AV片,免费一级做a爰片久久毛片潮,国产精品女人精品久久久天天,99久久久无码国产精品免费了

行業產品

  • 行業產品

上海榮計達儀器科技有限公司


當前位置:上海榮計達儀器科技有限公司>>瀝青實驗儀器>>LST-II瀝青混凝土滲透試驗儀

LST-II瀝青混凝土滲透試驗儀

返回列表頁
參  考  價面議
具體成交價以合同協議為準

產品型號LST-II

品       牌

廠商性質其他

所  在  地上海市

紡織服裝機械網采購部電話:0571-88918531QQ:2568841715

聯系方式:查看聯系方式

更新時間:2024-02-14 14:30:43瀏覽次數:82次

聯系我時,請告知來自 紡織服裝機械網

經營模式:其他

商鋪產品:1006條

所在地區:

聯系人:王林

產品簡介

瀝青混凝土滲透儀是檢測儀器,符合電力部水工瀝青混凝土試驗規程DL/T5326-2006的要求,用于測定瀝青混凝土的滲透系數。瀝青混凝土滲透儀符合DL/T5362-2006水工瀝青混凝土試驗規程測定瀝青混凝土的滲透系數。常用水頭試驗適用于滲透系數較大的試件,變水頭試驗適用于試件較小的試件。

詳細介紹

瀝青混凝土滲透儀是檢測儀器,符合電力部水工瀝青混凝土試驗規程DL/T5326-2006的要求,用于測定瀝青混凝土的滲透系數。使用前務必仔細閱讀說明書。并由**實驗人員操作,以避免操作不當引起的傷害。如需了解更多資料請與我公司客服人員聯系。

Asphalt concrete permeation meter is a testing instrument that meets the requirements of the Ministry of Electric Power's hydraulic asphalt concrete test regulations DL / T5326-2006, and is used to determine the permeability coefficient of asphalt concrete. Be sure to read the instructions carefully before use. It is operated by ** experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.


瀝青混凝土滲透儀符合DL/T5362-2006水工瀝青混凝土試驗規程測定瀝青混凝土的滲透系數。常用水頭試驗適用于滲透系數較大的試件,變水頭試驗適用于試件較小的試件。

The asphalt concrete permeation meter conforms to DL / T5362-2006 hydraulic asphalt concrete test procedures to determine the permeability coefficient of asphalt concrete. The common water head test is suitable for test pieces with large permeability coefficients, and the variable water head test is suitable for test pieces with smaller test pieces.


瀝青混凝土滲透儀由真空泵、真空壓力表、供水箱、閥門、集水瓶、出水側壓管、進水側壓管、試模等組成。每次同時可做兩組試驗。

The asphalt concrete permeation meter is composed of a vacuum pump, a vacuum pressure gauge, a water supply tank, a valve, a water collection bottle, an outlet pressure pipe, an inlet pressure pipe, and a test mold. Two sets of tests can be performed at a time.


瀝青混凝土滲透儀技術參數:

★真空泵功率:180W 220V

★真空壓力表:0 ~ -0.1MPa

★試模:¢101.6mm*63.5mm 2件 ¢152.4mm*95.3mm 2件

★外形尺寸:700mm*600mm*1400mm

★滲透試驗裝置及試模:滲透試驗裝置可用于變水頭試驗和常水頭滲透試驗。

★其他:量筒、秒表、溫度計、止水填料及加熱器具等。

Technical parameters of asphalt concrete infiltration meter:

★ Vacuum pump power: 180W 220V

★ Vacuum pressure gauge: 0 ~ -0.1MPa

★ Test mold: ¢ 101.6mm * 63.5mm 2 pieces ¢ 152.4mm * 95.3mm 2 pieces

★ Dimensions: 700mm * 600mm * 1400mm

★ Penetration test device and test mode: Penetration test device can be used for variable head test and constant head penetration test.

★ Others: measuring cylinders, stopwatches, thermometers, water-stop fillers and heating appliances.


瀝青混凝土滲透儀試驗步驟:

★按規范要求制備瀝青混合料(詳見附錄),按規范要求成型馬歇爾試件。如采用芯樣進行試驗,用切割機將芯樣上下兩頭切平,測量試件的平均高度和直徑。

★將滲透試模的上蓋卸下,將試件放入試模中間,清理試件表面,除去油污、粉塵等,避免試件周圍與瀝青結合不好而滲水,灌入熱瀝青密封試模與試件周邊的縫隙。灌縫時應避免熱瀝青污

★染試件表面及瀝青外流。待瀝青冷至室溫后,裝好上蓋, 擰緊螺栓。滲透試件裝模后,應加以檢查,確認試模密封良好、管道通暢。

★試驗應采用蒸餾水或經過濾的清水,試驗前用抽氣法或煮沸法進行排氣。試驗時水溫宜高于室溫3℃~4℃。試驗開始前應備夠一次試驗所需的用水。

Asphalt concrete permeameter test steps:

★ Asphalt mixture is prepared according to the specifications (see appendix for details), and Marshall test pieces are formed according to the specifications. If the core sample is used for the test, the upper and lower ends of the core sample are cut flat with a cutting machine, and the average height and diameter of the test piece are measured.

★ Remove the upper cover of the penetration test mold, place the test piece in the middle of the test mold, clean the surface of the test piece, remove oil, dust, etc., avoid the water around the test piece not being well bonded with the asphalt, and inject the hot asphalt to seal the test mold With the gap around the test piece. Avoid hot asphalt pollution when filling joints

★ Dyeing test piece surface and asphalt flow out. After the asphalt has cooled to room temperature, install the cover and tighten the bolts. After the penetration test piece is installed, it should be inspected to confirm that the test mold is well sealed and the pipeline is unobstructed.

★ The test should use distilled water or filtered water. Exhaust by the air extraction method or boiling method before the test. The water temperature should be 3 ℃ ~ 4 ℃ higher than the room temperature during the test. Before starting the test, sufficient water for one test should be prepared.



感興趣的產品PRODUCTS YOU ARE INTERESTED IN

紡織服裝機械網 設計制作,未經允許翻錄必究 .? ? ? Copyright(C)?2021 http://superheroescape.com,All rights reserved.

以上信息由企業自行提供,信息內容的真實性、準確性和合法性由相關企業負責,紡織服裝機械網對此不承擔任何保證責任。 溫馨提示:為規避購買風險,建議您在購買產品前務必確認供應商資質及產品質量。

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

登錄 后再收藏

提示

您的留言已提交成功!我們將在第一時間回復您~