石膏板材厚度測定儀是檢測儀器，用于測量石膏板材的厚度，也可用于測量其它材料的厚度，但需要根據所測材料和尺寸的不同要求，更換上下測頭(本儀器不帶附件)。如測鉆頭上螺旋槽的深度(用尖形測頭)；測木板、夾板、合成板等板材的厚度(用球形測頭)。
Gypsum board thickness tester is a testing instrument for measuring the thickness of gypsum board. It can also be used to measure the thickness of other materials. However, it is necessary to replace the upper and lower probes according to the different requirements of the measured material and size (this instrument does not have accessories) ). Such as measuring the depth of the spiral groove on the drill (using a pointed probe); measuring the thickness of wood, plywood, composite board and other plates (using a spherical probe).
石膏板材厚度測定儀主要技術參數：
測量范圍：0-30mm
讀出精度：0.01mm
握手架深度：116mm
凈重：1.5kg
Main technical parameters of gypsum board thickness tester:
Measuring range: 0-30mm
Reading accuracy: 0.01mm
Handshake frame depth: 116mm
Net weight: 1.5kg
石膏板材厚度測定儀結構及工作原理：
握手架開口端上邊按了一個百分表。由螺釘鎖緊：百分表原有球形測量頭換上了盤形測量頭，工作時壓下百分表的上端壓頭，可使百分表上的測量桿也同時下降，松手后依靠百分表上面的彈簧復位。握手架開口端上邊按了一個百分表，由螺釘鎖緊，百分表原有球形測量桿也同時下降。松手后依靠百分表上面的彈簧復位。握手架開口端的下邊按了一個測量頭，下測量頭靠M3推端緊定螺釘支撐及一個M3圓柱頭螺釘拉緊，這樣便于下測量頭調整到與上測量頭平行。
Structure and working principle of gypsum board thickness tester:
A dial indicator was pushed over the open end of the handshake. Tightened by screws: The original spherical measuring head of the dial indicator was replaced with a disc-shaped measuring head. When the upper end of the dial indicator is depressed during work, the measuring rod on the dial indicator can also be lowered at the same time. Spring return on the sub-meter. A dial indicator was pressed on the open end of the handshake frame and locked by screws. The original spherical measuring rod of the dial indicator was also lowered at the same time. After letting go, rely on the spring on the dial indicator to reset. A measuring head is pressed under the open end of the handshake frame. The lower measuring head is supported by the M3 pusher set screw and a M3 cylindrical head screw is tightened, so that the lower measuring head can be adjusted parallel to the upper measuring head.
石膏板材厚度測定儀操作使用與調整 使用前應檢查百分表上的大小指針是否指向零位，這樣可擰送螺釘調整百分表上下位置，然后旋緊，如大指針不在零位可轉動百分表殼加以調整。
上下測量頭接觸時，側面應全面接觸，不應傾斜，如有傾斜，可松動M3閥柱頭螺釘，然后調整推端緊定螺釘使全面接觸，然后將圓柱頭螺釘擰緊即可。 測量板材厚度時，可將半才嵌入兩端測量頭之間，上下測量桿，使兩測量頭與板材緊密接觸，此時即可在百分表上直接讀出被測板材的厚度，小指針指的為毫米整數，大指針指的為小數。
Gypsum board thickness tester operation and adjustment Before use, check whether the size pointer on the dial indicator points to zero, so that you can screw in to adjust the upper and lower positions of the dial indicator, and then tighten, if the large pointer is not in the zero position, you can turn the 100 Adjust the case.
When the upper and lower measuring heads are in contact, the sides should be in full contact and should not be tilted. If it is tilted, loosen the M3 valve head head screw, then adjust the pusher set screw to make full contact, and then tighten the cylinder head screw. When measuring the thickness of the plate, you can insert half of it between the measuring heads at both ends, and then move the measuring rod up and down so that the two measuring heads are in close contact with the plate. At this time, the thickness of the measured plate can be read directly on the dial indicator. Refers to integers in millimeters and large pointers to decimals.
石膏板材厚度測定儀維護與保養：
此儀器是精密量具，應輕拿輕放，禁止撞跌。使用完畢應用軟布擦拭干凈，妥為收藏，儀器平時不應隨便拆卸，以免損壞。
Gypsum board thickness tester maintenance
This instrument is a precision measuring tool. After use, wipe it with a soft cloth and store it properly. The instrument should not be disassembled in order to avoid damage.
QQ:2568841715
