榮計達 輪廓標耐密封測量裝置參數LKB-MF
LKB-MF 面議縫前設備 縫制設備 縫制配件 整理設備 繡花機 內衣機械 服裝輔助設備 洗滌機械 二手服裝機械 其它服裝機械
上海榮計達儀器科技有限公司
上海榮計達儀器科技有限公司
| 參 考 價 | 面議 |
產品型號YDT757
品 牌
廠商性質其他
所 在 地上海市
紡織服裝機械網采購部電話：0571-88918531
QQ:2568841715
聯系方式：查看聯系方式
更新時間：2023-10-15 12:47:03瀏覽次數：191次
聯系我時，請告知來自 紡織服裝機械網試驗裝置由錘頭、錘柄及底座三個構件組成。符合GB/T2694-2010、YDT757等標準的落錘試驗方法，適用于熱浸鍍鋅層附著力試驗，是利用錘頭自由跌落擊打試樣來測試鍍鋅層是否合標準。本產品適用于鐵塔類似生產廠家和質檢部門進行產品質量檢測和控制。
一、概述：
試驗裝置由錘頭、錘柄及底座三個構件組成。符合GB/T2694-2010、YDT757等標準的落錘試驗方法，適用于熱浸鍍鋅層附著力試驗，是利用錘頭自由跌落擊打試樣來測試鍍鋅層是否合標準。本產品適用于鐵塔類似生產廠家和質檢部門進行產品質量檢測和控制。
Overview of Hot Dip Galvanized Coating Adhesion Tester
The test device consists of a hammer head, a hammer handle and a base. The drop weight test methods that comply with GB / T2694-2010, YDT757 and other standards are applicable to the hot-dip galvanized coating adhesion test. The hammer head is used to freely hit the sample to test whether the galvanized layer meets the standard. This product is suitable for product quality inspection and control of similar tower manufacturers and quality inspection departments.
二、特點：
錘頭表面應光滑、平整、無毛刺。錘頭與錘柄結合應牢固；底座與錘柄之間穎活動靈活。外形尺寸錘頭、錘柄及底座公稱尺寸及允許偏差見表所示
Features of Hot Dip Galvanized Coating Adhesion Tester:
The surface of the hammer head should be smooth, flat and free of burrs. The combination of the hammer head and the hammer handle should be firm; the gliding movement between the base and the hammer handle should be flexible. The dimensions and allowable deviations of hammer head, hammer handle and base are shown in the table.
三、技術參數：
1、錘頭質量：210g±1g
2、錘頭心線至底座面垂直高度：300mm±1mm
3、錘柄材料：橡木
Technical parameters of hot dip galvanized layer adhesion tester
1. Mass of hammer head: 210g ± 1g
2. Vertical height from hammer head centerline to base surface: 300mm ± 1mm
3. Hammer handle material: Oak
四、使用方法：
試件置于水平，調整試樣，使打擊點距試樣邊、角、端部不小于10mm，錘頭面向臺架心，錘柄與底座平面垂直后自由落下，以4mm的間隔平行打擊5點。檢查鍍鋅層表面狀態是否符合標準要求，打擊處不得重復打擊.
How to use the hot-dip galvanized coating adhesion tester:
The test piece is placed on the level, and the specimen is adjusted so that the impact point is not less than 10mm from the edge, corner and end of the specimen. The hammer head faces the center of the stand. point. Check whether the surface condition of the galvanized layer meets the requirements of the standard. Do not repeat the strike at the strike.
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
紡織服裝機械網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
